Announcement

Collapse
No announcement yet.

Switching VT using the radeon driver.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Switching VT using the radeon driver.

    Hey guys,

    I'm using the 6.9.0 version of radeon and xorg-server-1.5.3 The problem that I'm having right now is when I try to switch VT I lose the connection to the monitor. The light on it turns amber and the screen goes dark. If I switch back to VT7, which is the X display, then it comes back on and works fine. But I cant switch to any other VT.


    Any suggestions? Advice? Questions?

    EDIT: Here is the relevant part of the Xorg.0.log
    Code:
    Output 51 disable success
    Blank CRTC 0 success
    Disable CRTC 0 success
    Blank CRTC 1 success
    Disable CRTC 1 success
    Enable CRTC 0 success
    Unblank CRTC 0 success
    Output 51 disable success
    Enable CRTC 0 success
    Unblank CRTC 0 success
    Output 51 enable success
    Output 51 disable success
    Blank CRTC 0 success
    Disable CRTC 0 success
    Enable CRTC 0 success
    Unblank CRTC 0 success
    Output 51 enable success
    (II) 3rd Button detected: disabling emulate3Button
    Output 51 disable success
    Blank CRTC 0 success
    Disable CRTC 0 success
    Blank CRTC 1 success
    Disable CRTC 1 success
    Enable CRTC 0 success
    Unblank CRTC 0 success
    Output 51 disable success
    Enable CRTC 0 success
    Unblank CRTC 0 success
    Output 51 enable success
    Output 51 disable success
    Blank CRTC 0 success
    Disable CRTC 0 success
    Enable CRTC 0 success
    Unblank CRTC 0 success
    Output 51 enable success
    (II) AIGLX: Suspending AIGLX clients for VT switch
    Output 51 disable success
    Blank CRTC 0 success
    Disable CRTC 0 success
    Blank CRTC 1 success
    Disable CRTC 1 success
    (II) RADEON(0): RADEONRestoreMemMapRegisters() : 
    (II) RADEON(0):   MC_FB_LOCATION   : 0xfffff000 0xdfffd000
    (II) RADEON(0):   MC_AGP_LOCATION  : 0x00000000
    (II) RADEON(0): avivo_restore !
    Enable CRTC 0 success
    Unblank CRTC 0 success
    (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
    (II) No APM support in BIOS or kernel
    (II) AIGLX: Resuming AIGLX clients after VT switch
    Static power management enable success
    Dynamic clock gating enable success
    Output 51 disable success
    Blank CRTC 0 success
    Disable CRTC 0 success
    Blank CRTC 1 success
    Disable CRTC 1 success
    Output 51 disable success
    Blank CRTC 0 success
    Disable CRTC 0 success
    Mode 1280x800 - 1760 841 0
    (II) RADEON(0): RADEONRestoreMemMapRegisters() : 
    (II) RADEON(0):   MC_FB_LOCATION   : 0xdfffd000 0xfffff000
    (II) RADEON(0):   MC_AGP_LOCATION  : 0xffffffc0
    freq: 111500000
    best_freq: 111500000
    best_feedback_div: 223
    best_ref_div: 6
    best_post_div: 9
    (II) RADEON(0): crtc(0) Clock: mode 111500, PLL 111500
    (II) RADEON(0): crtc(0) PLL  : refdiv 6, fbdiv 0xDF(223), pdiv 9
    Set CRTC PLL success
    Set CRTC Timing success
    Not using RMX
    scaler 0 setup success
    Set CRTC 0 Source success
    Output digital setup success
    Output 51 enable success
    Enable CRTC 0 success
    Unblank CRTC 0 success
    Blank CRTC 1 success
    Disable CRTC 1 success
    (II) RADEON(0): [RESUME] Attempting to re-init Radeon hardware.
    (II) Mouse0: ps2EnableDataReporting: succeeded
    (II) AIGLX: Suspending AIGLX clients for VT switch
    Output 51 disable success
    Blank CRTC 0 success
    Disable CRTC 0 success
    Blank CRTC 1 success
    Disable CRTC 1 success
    (II) RADEON(0): RADEONRestoreMemMapRegisters() : 
    (II) RADEON(0):   MC_FB_LOCATION   : 0xfffff000 0xdfffd000
    (II) RADEON(0):   MC_AGP_LOCATION  : 0x00000000
    (II) RADEON(0): avivo_restore !
    Enable CRTC 0 success
    Unblank CRTC 0 success
    (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
    (II) No APM support in BIOS or kernel
    (II) AIGLX: Resuming AIGLX clients after VT switch
    Static power management enable success
    Dynamic clock gating enable success
    Output 51 disable success
    Blank CRTC 0 success
    Disable CRTC 0 success
    Blank CRTC 1 success
    Disable CRTC 1 success
    Output 51 disable success
    Blank CRTC 0 success
    Disable CRTC 0 success
    Mode 1280x800 - 1760 841 0
    (II) RADEON(0): RADEONRestoreMemMapRegisters() : 
    (II) RADEON(0):   MC_FB_LOCATION   : 0xdfffd000 0xfffff000
    (II) RADEON(0):   MC_AGP_LOCATION  : 0xffffffc0
    freq: 111500000
    best_freq: 111500000
    best_feedback_div: 223
    best_ref_div: 6
    best_post_div: 9
    (II) RADEON(0): crtc(0) Clock: mode 111500, PLL 111500
    (II) RADEON(0): crtc(0) PLL  : refdiv 6, fbdiv 0xDF(223), pdiv 9
    Set CRTC PLL success
    Set CRTC Timing success
    Not using RMX
    scaler 0 setup success
    Set CRTC 0 Source success
    Output digital setup success
    Output 51 enable success
    Enable CRTC 0 success
    Unblank CRTC 0 success
    Blank CRTC 1 success
    Disable CRTC 1 success
    (II) RADEON(0): [RESUME] Attempting to re-init Radeon hardware.
    (II) Mouse0: ps2EnableDataReporting: succeeded
    LiveDVD user #
    Last edited by duby229; 30 December 2008, 08:13 PM.

  • #2
    what chip and connector type (DVI, VGA, HMDI, etc.) are you using?

    Comment


    • #3
      Originally posted by agd5f View Post
      what chip and connector type (DVI, VGA, HMDI, etc.) are you using?
      It's an x1950Pro PCIe connected to the DVI port. I'm re-installing acpid right now to see if that resolves the issue. I'll let you know in a minute.

      Comment


      • #4
        OK updating acpid fixed the problem where is couldnt open acpid.socket, but it still wont allow me to switch VT. I still get an amber light on the monitor and the monitor still goes dark when I switch.

        Here is my complete Xorg.0.log

        Pastebin.com is the number one paste tool since 2002. Pastebin is a website where you can store text online for a set period of time.

        Comment


        • #5
          Hey, I'm having the exact same issue with my PCIe X1950 Pro, also connected via DVI. I can't switch VTs either. The monitor flashes the "No signal" window, then blanks itself. It thinks it has no video signal unless it's on VT7.

          The difference between my log and yours is that I don't have the warnings (WW) about acpid; that's working correctly on my system.

          Comment


          • #6
            Originally posted by nightmorph View Post
            Hey, I'm having the exact same issue with my PCIe X1950 Pro, also connected via DVI. I can't switch VTs either. The monitor flashes the "No signal" window, then blanks itself. It thinks it has no video signal unless it's on VT7.

            The difference between my log and yours is that I don't have the warnings (WW) about acpid; that's working correctly on my system.
            OK, well, I fixed the acpid issue last night, and I'm still having the same problem. At least now I know I'm not alone. Thanks for posting this news.

            Comment


            • #7
              Originally posted by duby229 View Post
              OK, well, I fixed the acpid issue last night, and I'm still having the same problem. At least now I know I'm not alone. Thanks for posting this news.
              I'm experiencing a similar issue when KMS is enabled:


              But my card is an AGP Radeon 9500 and my monitor is CRT so I don't know if it's the same issue.

              Comment


              • #8
                Try this in your "radeon" driver section:

                Option "VGAAccess" "off"

                It probably won't help, but worth a shot.

                Edit:
                Try a full reboot after changing this option rather than just restarting X so that you can be sure the hardware has been reset also.
                Last edited by RealNC; 31 December 2008, 10:27 AM.

                Comment


                • #9
                  Does the console work if X doesn't start up? My point is, are you sure the problem is due to the Xorg driver?

                  Comment


                  • #10
                    Originally posted by TechMage89 View Post
                    Does the console work if X doesn't start up? My point is, are you sure the problem is due to the Xorg driver?

                    Sorry for the late reply. Its been one helluva night! Happy New Year!

                    I'd say that it is definitely the radeon driver. If I reboot the computer using the vesa driver or the radeonhd driver I can switch terminals just fine. This issue only occurs when using the radeon driver.

                    Comment

                    Working...
                    X