Intel P55 Chipset Preview On Linux
Written by Michael Larabel in Motherboards on 8 September 2009. Page 3 of 4. 2 Comments

00:00.0 Host bridge: Intel Corporation Clarksfield/Lynnfield DMI (rev 11)
00:03.0 PCI bridge: Intel Corporation Clarksfield/Lynnfield PCI Express Root Port 1 (rev 11)
00:08.0 System peripheral: Intel Corporation Clarksfield/Lynnfield System Management Registers (rev 11)
00:08.1 System peripheral: Intel Corporation Clarksfield/Lynnfield Semaphore and Scratchpad Registers (rev 11)
00:08.2 System peripheral: Intel Corporation Clarksfield/Lynnfield System Control and Status Registers (rev 11)
00:08.3 System peripheral: Intel Corporation Clarksfield/Lynnfield Miscellaneous Registers (rev 11)
00:10.0 System peripheral: Intel Corporation QPI Link (rev 11)
00:10.1 System peripheral: Intel Corporation QPI Routing and Protocol Registers (rev 11)
00:19.0 Ethernet controller: Intel Corporation 82578DC Gigabit Network Connection (rev 05)
00:1a.0 USB Controller: Intel Corporation Ibex Peak USB2 Enhanced Host Controller (rev 05)
00:1b.0 Audio device: Intel Corporation Ibex Peak High Definition Audio (rev 05)
00:1c.0 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 1 (rev 05)
00:1c.4 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 5 (rev 05)
00:1c.6 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 7 (rev 05)
00:1c.7 PCI bridge: Intel Corporation Ibex Peak PCI Express Root Port 8 (rev 05)
00:1d.0 USB Controller: Intel Corporation Ibex Peak USB2 Enhanced Host Controller (rev 05)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a5)
00:1f.0 ISA bridge: Intel Corporation Ibex Peak LPC Interface Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation Ibex Peak 6 port SATA AHCI Controller (rev 05)
00:1f.3 SMBus: Intel Corporation Ibex Peak SMBus Controller (rev 05)
01:00.0 VGA compatible controller: nVidia Corporation G92 [GeForce 9800 GTX] (rev a2)
05:00.0 IDE interface: Marvell Technology Group Ltd. 88SE6145 SATA II PCI-E controller (rev a1)
06:03.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)

 

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.31-9-generic (buildd@crested) (gcc version 4.4.1 (Ubuntu 4.4.1-3ubuntu3) ) #29-Ubuntu SMP Sun Aug 30 17:39:26 UTC 2009 (Ubuntu 2.6.31-9.29-generic)
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.31-9-generic root=UUID=56e1fb20-a4a0-4a11-9b62-e0a608ae7f51 ro quiet splash
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000008f000 (usable)
[ 0.000000] BIOS-e820: 000000000008f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007dd4a000 (usable)
[ 0.000000] BIOS-e820: 000000007dd4a000 - 000000007ddea000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007ddea000 - 000000007f671000 (usable)
[ 0.000000] BIOS-e820: 000000007f671000 - 000000007f6bf000 (reserved)
[ 0.000000] BIOS-e820: 000000007f6bf000 - 000000007f75d000 (usable)
[ 0.000000] BIOS-e820: 000000007f75d000 - 000000007f7bf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007f7bf000 - 000000007f7e8000 (usable)
[ 0.000000] BIOS-e820: 000000007f7e8000 - 000000007f7f1000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007f7f1000 - 000000007f7f2000 (usable)
[ 0.000000] BIOS-e820: 000000007f7f2000 - 000000007f7ff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007f7ff000 - 000000007f800000 (usable)
[ 0.000000] BIOS-e820: 000000007f800000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.5 present.
[ 0.000000] last_pfn = 0x7f800 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-DFFFF write-protect
[ 0.000000] E0000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 disabled
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] e820 update range: 0000000000001000 - 0000000000006000 (usable) ==> (reserved)
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000001000 (usable)
[ 0.000000] modified: 0000000000001000 - 0000000000006000 (reserved)
[ 0.000000] modified: 0000000000006000 - 000000000008f000 (usable)
[ 0.000000] modified: 000000000008f000 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 000000007dd4a000 (usable)
[ 0.000000] modified: 000000007dd4a000 - 000000007ddea000 (ACPI NVS)
[ 0.000000] modified: 000000007ddea000 - 000000007f671000 (usable)
[ 0.000000] modified: 000000007f671000 - 000000007f6bf000 (reserved)
[ 0.000000] modified: 000000007f6bf000 - 000000007f75d000 (usable)
[ 0.000000] modified: 000000007f75d000 - 000000007f7bf000 (ACPI NVS)
[ 0.000000] modified: 000000007f7bf000 - 000000007f7e8000 (usable)
[ 0.000000] modified: 000000007f7e8000 - 000000007f7f1000 (ACPI data)
[ 0.000000] modified: 000000007f7f1000 - 000000007f7f2000 (usable)
[ 0.000000] modified: 000000007f7f2000 - 000000007f7ff000 (ACPI data)
[ 0.000000] modified: 000000007f7ff000 - 000000007f800000 (usable)
[ 0.000000] modified: 000000007f800000 - 0000000080000000 (reserved)
[ 0.000000] modified: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] modified: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-000000007f800000
[ 0.000000] Using x86 segment limits to approximate NX protection
[ 0.000000] 0000000000 - 007f800000 page 2M
[ 0.000000] kernel direct mapping tables up to 7f800000 @ 8000-b000
[ 0.000000] RAMDISK: 378ef000 - 37fefc28
[ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL )
[ 0.000000] ACPI: XSDT 000000007f7fd120 0006C (v01 INTEL KBIBX10J 00000C86 01000013)
[ 0.000000] ACPI: FACP 000000007f7fc000 000F4 (v03 INTEL KBIBX10J 00000C86 MSFT 0100000D)
[ 0.000000] ACPI: DSDT 000000007f7f8000 03BF5 (v02 INTEL KBIBX10J 00000C86 MSFT 0100000D)
[ 0.000000] ACPI: FACS 000000007f76c000 00040
[ 0.000000] ACPI: APIC 000000007f7f7000 000BC (v02 INTEL KBIBX10J 00000C86 MSFT 0100000D)
[ 0.000000] ACPI: WDDT 000000007f7f6000 00040 (v01 INTEL KBIBX10J 00000C86 MSFT 0100000D)
[ 0.000000] ACPI: MCFG 000000007f7f5000 0003C (v01 INTEL KBIBX10J 00000C86 MSFT 0100000D)
[ 0.000000] ACPI: ASF! 000000007f7f4000 000A5 (v32 INTEL KBIBX10J 00000C86 MSFT 0100000D)
[ 0.000000] ACPI: HPET 000000007f7f3000 00038 (v01 INTEL KBIBX10J 00000C86 MSFT 0100000D)
[ 0.000000] ACPI: WDTx 000000007f7f0000 00224 (v02 INTEL KBIBX10J 00000C86 MSFT 0100000D)
[ 0.000000] ACPI: SSDT 000000007f7e9000 06F74 (v01 INTEL SSDT PM 00000C86 MSFT 0100000D)
[ 0.000000] ACPI: ASPT 000000007f7f2000 00034 (v05 INTEL PerfTune 00000C86 MSFT 0100000D)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007f800000
[ 0.000000] Bootmem setup node 0 0000000000000000-000000007f800000
[ 0.000000] NODE_DATA [0000000000009000 - 000000000000dfff]
[ 0.000000] bootmap [000000000000e000 - 000000000001deff] pages 10
[ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 007f800000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0001000000 - 00019b2b8c] TEXT DATA BSS ==> [0001000000 - 00019b2b8c]
[ 0.000000] #3 [00378ef000 - 0037fefc28] RAMDISK ==> [00378ef000 - 0037fefc28]
[ 0.000000] #4 [000009d000 - 0000100000] BIOS reserved ==> [000009d000 - 0000100000]
[ 0.000000] #5 [00019b3000 - 00019b315e] BRK ==> [00019b3000 - 00019b315e]
[ 0.000000] #6 [0000008000 - 0000009000] PGTABLE ==> [0000008000 - 0000009000]
[ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880001e00000-ffff8800039fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[8] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00000001
[ 0.000000] 0: 0x00000006 -> 0x0000008f
[ 0.000000] 0: 0x00000100 -> 0x0007dd4a
[ 0.000000] 0: 0x0007ddea -> 0x0007f671
[ 0.000000] 0: 0x0007f6bf -> 0x0007f75d
[ 0.000000] 0: 0x0007f7bf -> 0x0007f7e8
[ 0.000000] 0: 0x0007f7f1 -> 0x0007f7f2
[ 0.000000] 0: 0x0007f7ff -> 0x0007f800
[ 0.000000] On node 0 totalpages: 521764
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 103 pages reserved
[ 0.000000] DMA zone: 3819 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7084 pages used for memmap
[ 0.000000] DMA32 zone: 510702 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] SMP: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 0000000000001000 - 0000000000006000
[ 0.000000] PM: Registered nosave memory: 000000000008f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007dd4a000 - 000000007ddea000
[ 0.000000] PM: Registered nosave memory: 000000007f671000 - 000000007f6bf000
[ 0.000000] PM: Registered nosave memory: 000000007f75d000 - 000000007f7bf000
[ 0.000000] PM: Registered nosave memory: 000000007f7e8000 - 000000007f7f1000
[ 0.000000] PM: Registered nosave memory: 000000007f7f2000 - 000000007f7ff000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:78000000)
[ 0.000000] NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages at ffff8800019c5000, static data 89952 bytes
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 514521
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.31-9-generic root=UUID=56e1fb20-a4a0-4a11-9b62-e0a608ae7f51 ro quiet splash
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 2040180k/2088960k available (5279k kernel code, 1904k absent, 46876k reserved, 2987k data, 656k init)
[ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] NR_IRQS:4352 nr_irqs:472
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2667.263 MHz processor.
[ 0.002081] Console: colour VGA+ 80x25
[ 0.002083] console [tty0] enabled
[ 0.005871] allocated 20971520 bytes of page_cgroup
[ 0.005873] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.006004] hpet clockevent registered
[ 0.006015] alloc irq_desc for 24 on node 0
[ 0.006018] alloc kstat_irqs on node 0
[ 0.006027] alloc irq_desc for 25 on node 0
[ 0.006028] alloc kstat_irqs on node 0
[ 0.006035] alloc irq_desc for 26 on node 0
[ 0.006036] alloc kstat_irqs on node 0
[ 0.006041] alloc irq_desc for 27 on node 0
[ 0.006042] alloc kstat_irqs on node 0
[ 0.006045] alloc irq_desc for 28 on node 0
[ 0.006046] alloc kstat_irqs on node 0
[ 0.006048] HPET: 8 timers in total, 5 timers will be used for per-cpu timer
[ 0.006053] Calibrating delay loop (skipped), value calculated using timer frequency.. 5334.52 BogoMIPS (lpj=10669052)
[ 0.006067] Security Framework initialized
[ 0.006080] AppArmor: AppArmor initialized
[ 0.006199] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.006607] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.006789] Mount-cache hash table entries: 256
[ 0.006869] Initializing cgroup subsys ns
[ 0.006871] Initializing cgroup subsys cpuacct
[ 0.006874] Initializing cgroup subsys memory
[ 0.006878] Initializing cgroup subsys freezer
[ 0.006879] Initializing cgroup subsys net_cls
[ 0.006888] CPU: Physical Processor ID: 0
[ 0.006889] CPU: Processor Core ID: 0
[ 0.006891] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.006893] CPU: L2 cache: 256K
[ 0.006894] CPU: L3 cache: 8192K
[ 0.006896] CPU 0/0x0 -> Node 0
[ 0.006898] using mwait in idle threads.
[ 0.006899] Performance Counters: Nehalem/Corei7 events, Intel PMU driver.
[ 0.006903] ... version: 3
[ 0.006904] ... bit width: 48
[ 0.006905] ... generic counters: 4
[ 0.006906] ... value mask: 0000ffffffffffff
[ 0.006907] ... max period: 000000007fffffff
[ 0.006908] ... fixed-purpose counters: 3
[ 0.006909] ... counter mask: 000000070000000f
[ 0.008487] ACPI: Core revision 20090521
[ 0.015394] Setting APIC routing to flat
[ 0.015754] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.055343] CPU0: Intel(R) Core(TM) CPU 750 @ 2.67GHz stepping 05
[ 0.161702] Booting processor 1 APIC 0x2 ip 0x6000
[ 0.172091] Initializing CPU#1
[ 0.249386] Calibrating delay using timer specific routine.. 5333.32 BogoMIPS (lpj=10666655)
[ 0.249392] CPU: Physical Processor ID: 0
[ 0.249393] CPU: Processor Core ID: 1
[ 0.249395] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.249396] CPU: L2 cache: 256K
[ 0.249397] CPU: L3 cache: 8192K
[ 0.249399] CPU 1/0x2 -> Node 0
[ 0.249832] CPU1: Intel(R) Core(TM) CPU 750 @ 2.67GHz stepping 05
[ 0.249843] Skipping synchronization checks as TSC is reliable.
[ 0.249909] Booting processor 2 APIC 0x4 ip 0x6000
[ 0.260166] Initializing CPU#2
[ 0.337156] Calibrating delay using timer specific routine.. 5333.32 BogoMIPS (lpj=10666641)
[ 0.337162] CPU: Physical Processor ID: 0
[ 0.337163] CPU: Processor Core ID: 2
[ 0.337165] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.337166] CPU: L2 cache: 256K
[ 0.337167] CPU: L3 cache: 8192K
[ 0.337168] CPU 2/0x4 -> Node 0
[ 0.337637] CPU2: Intel(R) Core(TM) CPU 750 @ 2.67GHz stepping 05
[ 0.337648] Skipping synchronization checks as TSC is reliable.
[ 0.337716] Booting processor 3 APIC 0x6 ip 0x6000
[ 0.347873] Initializing CPU#3
[ 0.424926] Calibrating delay using timer specific routine.. 5333.31 BogoMIPS (lpj=10666631)
[ 0.424932] CPU: Physical Processor ID: 0
[ 0.424933] CPU: Processor Core ID: 3
[ 0.424935] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.424936] CPU: L2 cache: 256K
[ 0.424937] CPU: L3 cache: 8192K
[ 0.424938] CPU 3/0x6 -> Node 0
[ 0.425345] CPU3: Intel(R) Core(TM) CPU 750 @ 2.67GHz stepping 05
[ 0.425357] Skipping synchronization checks as TSC is reliable.
[ 0.425371] Brought up 4 CPUs
[ 0.425373] Total of 4 processors activated (21334.48 BogoMIPS).
[ 0.425425] CPU0 attaching sched-domain:
[ 0.425427] domain 0: span 0-3 level MC
[ 0.425429] groups: 0 1 2 3
[ 0.425433] CPU1 attaching sched-domain:
[ 0.425434] domain 0: span 0-3 level MC
[ 0.425436] groups: 1 2 3 0
[ 0.425439] CPU2 attaching sched-domain:
[ 0.425440] domain 0: span 0-3 level MC
[ 0.425441] groups: 2 3 0 1
[ 0.425444] CPU3 attaching sched-domain:
[ 0.425446] domain 0: span 0-3 level MC
[ 0.425447] groups: 3 0 1 2
[ 0.425760] Booting paravirtualized kernel on bare hardware
[ 0.425893] regulator: core version 0.5
[ 0.425931] Time: 23:37:13 Date: 09/04/09
[ 0.425962] NET: Registered protocol family 16
[ 0.426231] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.426233] ACPI: bus type pci registered
[ 0.426333] PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
[ 0.426335] PCI: MCFG area at f8000000 reserved in E820
[ 0.426885] PCI: Using MMCONFIG at f8000000 - fbffffff
[ 0.426887] PCI: Using configuration type 1 for base access
[ 0.429171] bio: create slab <bio-0> at 0
[ 0.429797] ACPI: EC: Look up EC in DSDT
[ 0.437821] ACPI: Interpreter enabled
[ 0.437824] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.437838] ACPI: Using IOAPIC for interrupt routing
[ 0.441121] ACPI: No dock devices found.
[ 0.441276] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.441569] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[ 0.441572] pci 0000:00:03.0: PME# disabled
[ 0.441827] pci 0000:00:19.0: reg 10 32bit mmio: [0x93200000-0x9321ffff]
[ 0.441836] pci 0000:00:19.0: reg 14 32bit mmio: [0x93224000-0x93224fff]
[ 0.441846] pci 0000:00:19.0: reg 18 io port: [0x3040-0x305f]
[ 0.441884] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.441891] pci 0000:00:19.0: PME# disabled
[ 0.441939] pci 0000:00:1a.0: reg 10 32bit mmio: [0x93225c00-0x93225fff]
[ 0.441996] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.442004] pci 0000:00:1a.0: PME# disabled
[ 0.442047] pci 0000:00:1b.0: reg 10 64bit mmio: [0x93220000-0x93223fff]
[ 0.442091] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.442099] pci 0000:00:1b.0: PME# disabled
[ 0.442161] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.442169] pci 0000:00:1c.0: PME# disabled
[ 0.442226] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.442234] pci 0000:00:1c.4: PME# disabled
[ 0.442304] pci 0000:00:1c.6: PME# supported from D0 D3hot D3cold
[ 0.442311] pci 0000:00:1c.6: PME# disabled
[ 0.442366] pci 0000:00:1c.7: PME# supported from D0 D3hot D3cold
[ 0.442373] pci 0000:00:1c.7: PME# disabled
[ 0.442423] pci 0000:00:1d.0: reg 10 32bit mmio: [0x93225800-0x93225bff]
[ 0.442480] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.442487] pci 0000:00:1d.0: PME# disabled
[ 0.442671] pci 0000:00:1f.2: reg 10 io port: [0x3068-0x306f]
[ 0.442680] pci 0000:00:1f.2: reg 14 io port: [0x3074-0x3077]
[ 0.442690] pci 0000:00:1f.2: reg 18 io port: [0x3060-0x3067]
[ 0.442699] pci 0000:00:1f.2: reg 1c io port: [0x3070-0x3073]
[ 0.442708] pci 0000:00:1f.2: reg 20 io port: [0x3020-0x303f]
[ 0.442717] pci 0000:00:1f.2: reg 24 32bit mmio: [0x93225000-0x932257ff]
[ 0.442749] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.442756] pci 0000:00:1f.2: PME# disabled
[ 0.442784] pci 0000:00:1f.3: reg 10 64bit mmio: [0x93226000-0x932260ff]
[ 0.442800] pci 0000:00:1f.3: reg 20 io port: [0x3000-0x301f]
[ 0.442849] pci 0000:01:00.0: reg 10 32bit mmio: [0x92000000-0x92ffffff]
[ 0.442857] pci 0000:01:00.0: reg 14 64bit mmio: [0x80000000-0x8fffffff]
[ 0.442864] pci 0000:01:00.0: reg 1c 64bit mmio: [0x90000000-0x91ffffff]
[ 0.442869] pci 0000:01:00.0: reg 24 io port: [0x2000-0x207f]
[ 0.442873] pci 0000:01:00.0: reg 30 32bit mmio: [0xfffe0000-0xffffffff]
[ 0.442916] pci 0000:00:03.0: bridge io port: [0x2000-0x2fff]
[ 0.442919] pci 0000:00:03.0: bridge 32bit mmio: [0x90000000-0x92ffffff]
[ 0.442923] pci 0000:00:03.0: bridge 64bit mmio pref: [0x80000000-0x8fffffff]
[ 0.443102] pci 0000:05:00.0: reg 10 io port: [0x1018-0x101f]
[ 0.443113] pci 0000:05:00.0: reg 14 io port: [0x1024-0x1027]
[ 0.443124] pci 0000:05:00.0: reg 18 io port: [0x1010-0x1017]
[ 0.443135] pci 0000:05:00.0: reg 1c io port: [0x1020-0x1023]
[ 0.443145] pci 0000:05:00.0: reg 20 io port: [0x1000-0x100f]
[ 0.443156] pci 0000:05:00.0: reg 24 32bit mmio: [0x93100000-0x931003ff]
[ 0.443168] pci 0000:05:00.0: reg 30 32bit mmio: [0xfffc0000-0xffffffff]
[ 0.443203] pci 0000:05:00.0: supports D1
[ 0.443204] pci 0000:05:00.0: PME# supported from D0 D1 D3hot
[ 0.443212] pci 0000:05:00.0: PME# disabled
[ 0.443259] pci 0000:00:1c.7: bridge io port: [0x1000-0x1fff]
[ 0.443266] pci 0000:00:1c.7: bridge 32bit mmio: [0x93100000-0x931fffff]
[ 0.443312] pci 0000:06:03.0: reg 10 32bit mmio: [0x93004000-0x930047ff]
[ 0.443322] pci 0000:06:03.0: reg 14 32bit mmio: [0x93000000-0x93003fff]
[ 0.443365] pci 0000:06:03.0: supports D1 D2
[ 0.443367] pci 0000:06:03.0: PME# supported from D0 D1 D2 D3hot
[ 0.443374] pci 0000:06:03.0: PME# disabled
[ 0.443417] pci 0000:00:1e.0: transparent bridge
[ 0.443426] pci 0000:00:1e.0: bridge 32bit mmio: [0x93000000-0x930fffff]
[ 0.443461] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.443762] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[ 0.443874] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 0.443928] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[ 0.443977] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6._PRT]
[ 0.444025] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX7._PRT]
[ 0.444084] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT]
[ 0.448016] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.448110] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.448205] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 *10 11 12)
[ 0.448297] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *9 10 11 12)
[ 0.448387] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 *10 11 12)
[ 0.448477] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.448571] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.448663] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 *9 10 11 12)
[ 0.448910] SCSI subsystem initialized
[ 0.448957] libata version 3.00 loaded.
[ 0.449064] usbcore: registered new interface driver usbfs
[ 0.449085] usbcore: registered new interface driver hub
[ 0.449112] usbcore: registered new device driver usb
[ 0.449340] ACPI: WMI: Mapper loaded
[ 0.449342] PCI: Using ACPI for IRQ routing
[ 0.468831] Bluetooth: Core ver 2.15
[ 0.468899] NET: Registered protocol family 31
[ 0.468902] Bluetooth: HCI device and connection manager initialized
[ 0.468905] Bluetooth: HCI socket layer initialized
[ 0.468908] NetLabel: Initializing
[ 0.468910] NetLabel: domain hash size = 128
[ 0.468912] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.468930] NetLabel: unlabeled traffic allowed by default
[ 0.468994] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 24, 25, 26, 27, 28, 0
[ 0.468999] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.472841] hpet: hpet2 irq 24 for MSI
[ 0.473257] hpet: hpet3 irq 25 for MSI
[ 0.477260] hpet: hpet4 irq 26 for MSI
[ 0.481251] hpet: hpet5 irq 27 for MSI
[ 0.484860] Switched to high resolution mode on CPU 0
[ 0.485265] Switched to high resolution mode on CPU 1
[ 0.485269] Switched to high resolution mode on CPU 3
[ 0.485274] Switched to high resolution mode on CPU 2
[ 0.500822] pnp: PnP ACPI init
[ 0.500834] ACPI: bus type pnp registered
[ 0.501915] pnp: PnP ACPI: found 10 devices
[ 0.501917] ACPI: ACPI bus type pnp unregistered
[ 0.501923] system 00:01: iomem range 0xf8000000-0xfbffffff has been reserved
[ 0.501925] system 00:01: iomem range 0xfeb00000-0xfeb03fff has been reserved
[ 0.501927] system 00:01: iomem range 0xfed10000-0xfed13fff has been reserved
[ 0.501929] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
[ 0.501931] system 00:01: iomem range 0xfed1b000-0xfed1bfff has been reserved
[ 0.501933] system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
[ 0.501935] system 00:01: iomem range 0xfed1a000-0xfed1afff has been reserved
[ 0.501937] system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.501939] system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.501941] system 00:01: iomem range 0xfed45000-0xfed99fff has been reserved
[ 0.501943] system 00:01: iomem range 0xc0000-0xdffff has been reserved
[ 0.501945] system 00:01: iomem range 0xe0000-0xfffff could not be reserved
[ 0.501947] system 00:01: iomem range 0xff000000-0xffffffff could not be reserved
[ 0.501951] system 00:06: ioport range 0x500-0x57f has been reserved
[ 0.501953] system 00:06: ioport range 0x400-0x47f has been reserved
[ 0.501955] system 00:06: ioport range 0x680-0x6ff has been reserved
[ 0.506720] AppArmor: AppArmor Filesystem Enabled
[ 0.506730] pci 0000:01:00.0: BAR 6: no parent found for of device [0xfffe0000-0xffffffff]
[ 0.506828] pci 0000:05:00.0: BAR 6: no parent found for of device [0xfffc0000-0xffffffff]
[ 0.506973] pci 0000:01:00.0: BAR 6: can't allocate mem resource [0x90000000-0x8fffffff]
[ 0.506976] pci 0000:00:03.0: PCI bridge, secondary bus 0000:01
[ 0.506978] pci 0000:00:03.0: IO window: 0x2000-0x2fff
[ 0.506981] pci 0000:00:03.0: MEM window: 0x90000000-0x92ffffff
[ 0.506984] pci 0000:00:03.0: PREFETCH window: 0x00000080000000-0x0000008fffffff
[ 0.506988] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.506989] pci 0000:00:1c.0: IO window: disabled
[ 0.506997] pci 0000:00:1c.0: MEM window: disabled
[ 0.506999] pci 0000:00:1c.0: PREFETCH window: disabled
[ 0.507006] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03
[ 0.507008] pci 0000:00:1c.4: IO window: disabled
[ 0.507015] pci 0000:00:1c.4: MEM window: disabled
[ 0.507022] pci 0000:00:1c.4: PREFETCH window: disabled
[ 0.507030] pci 0000:00:1c.6: PCI bridge, secondary bus 0000:04
[ 0.507031] pci 0000:00:1c.6: IO window: disabled
[ 0.507039] pci 0000:00:1c.6: MEM window: disabled
[ 0.507046] pci 0000:00:1c.6: PREFETCH window: disabled
[ 0.507054] pci 0000:00:1c.7: PCI bridge, secondary bus 0000:05
[ 0.507060] pci 0000:00:1c.7: IO window: 0x1000-0x1fff
[ 0.507068] pci 0000:00:1c.7: MEM window: 0x93100000-0x931fffff
[ 0.507075] pci 0000:00:1c.7: PREFETCH window: 0x93300000-0x933fffff
[ 0.507083] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:06
[ 0.507084] pci 0000:00:1e.0: IO window: disabled
[ 0.507093] pci 0000:00:1e.0: MEM window: 0x93000000-0x930fffff
[ 0.507100] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.507112] alloc irq_desc for 16 on node 0
[ 0.507113] alloc kstat_irqs on node 0
[ 0.507117] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.507119] pci 0000:00:03.0: setting latency timer to 64
[ 0.507128] alloc irq_desc for 17 on node 0
[ 0.507129] alloc kstat_irqs on node 0
[ 0.507132] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.507138] pci 0000:00:1c.0: setting latency timer to 64
[ 0.507147] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.507156] pci 0000:00:1c.4: setting latency timer to 64
[ 0.507165] alloc irq_desc for 18 on node 0
[ 0.507166] alloc kstat_irqs on node 0
[ 0.507169] pci 0000:00:1c.6: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.507175] pci 0000:00:1c.6: setting latency timer to 64
[ 0.507184] alloc irq_desc for 19 on node 0
[ 0.507185] alloc kstat_irqs on node 0
[ 0.507187] pci 0000:00:1c.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.507193] pci 0000:00:1c.7: setting latency timer to 64
[ 0.507202] pci 0000:00:1e.0: setting latency timer to 64
[ 0.507209] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.507210] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.507212] pci_bus 0000:01: resource 0 io: [0x2000-0x2fff]
[ 0.507214] pci_bus 0000:01: resource 1 mem: [0x90000000-0x92ffffff]
[ 0.507215] pci_bus 0000:01: resource 2 pref mem [0x80000000-0x8fffffff]
[ 0.507217] pci_bus 0000:05: resource 0 io: [0x1000-0x1fff]
[ 0.507219] pci_bus 0000:05: resource 1 mem: [0x93100000-0x931fffff]
[ 0.507220] pci_bus 0000:05: resource 2 pref mem [0x93300000-0x933fffff]
[ 0.507222] pci_bus 0000:06: resource 1 mem: [0x93000000-0x930fffff]
[ 0.507224] pci_bus 0000:06: resource 3 io: [0x00-0xffff]
[ 0.507225] pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.507246] NET: Registered protocol family 2
[ 0.507333] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.507765] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.508963] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.509242] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.509244] TCP reno registered
[ 0.509312] NET: Registered protocol family 1
[ 0.509352] Trying to unpack rootfs image as initramfs...
[ 0.633428] Freeing initrd memory: 7171k freed
[ 0.635008] Scanning for low memory corruption every 60 seconds
[ 0.635173] audit: initializing netlink socket (disabled)
[ 0.635183] type=2000 audit(1252107433.520:1): initialized
[ 0.642974] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.644716] VFS: Disk quotas dquot_6.5.2
[ 0.644771] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.645444] fuse init (API version 7.12)
[ 0.645542] msgmni has been set to 3998
[ 0.645696] alg: No test for stdrng (krng)
[ 0.645703] io scheduler noop registered
[ 0.645704] io scheduler anticipatory registered
[ 0.645706] io scheduler deadline registered
[ 0.645754] io scheduler cfq registered (default)
[ 0.676440] pci 0000:01:00.0: Boot video device
[ 0.676577] alloc irq_desc for 29 on node 0
[ 0.676579] alloc kstat_irqs on node 0
[ 0.676585] pcieport-driver 0000:00:03.0: irq 29 for MSI/MSI-X
[ 0.676591] pcieport-driver 0000:00:03.0: setting latency timer to 64
[ 0.676728] alloc irq_desc for 30 on node 0
[ 0.676729] alloc kstat_irqs on node 0
[ 0.676740] pcieport-driver 0000:00:1c.0: irq 30 for MSI/MSI-X
[ 0.676750] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 0.676890] alloc irq_desc for 31 on node 0
[ 0.676891] alloc kstat_irqs on node 0
[ 0.676901] pcieport-driver 0000:00:1c.4: irq 31 for MSI/MSI-X
[ 0.676912] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[ 0.677051] alloc irq_desc for 32 on node 0
[ 0.677052] alloc kstat_irqs on node 0
[ 0.677063] pcieport-driver 0000:00:1c.6: irq 32 for MSI/MSI-X
[ 0.677073] pcieport-driver 0000:00:1c.6: setting latency timer to 64
[ 0.677211] alloc irq_desc for 33 on node 0
[ 0.677212] alloc kstat_irqs on node 0
[ 0.677222] pcieport-driver 0000:00:1c.7: irq 33 for MSI/MSI-X
[ 0.677233] pcieport-driver 0000:00:1c.7: setting latency timer to 64
[ 0.677329] aer 0000:00:03.0:pcie02: AER service couldn't init device: no _OSC support
[ 0.677351] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.677444] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.677600] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 0.677603] ACPI: Power Button [PWRF]
[ 0.677654] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1
[ 0.677662] ACPI: Sleep Button [SLPB]
[ 0.678229] Monitor-Mwait will be used to enter C-1 state
[ 0.678244] Monitor-Mwait will be used to enter C-2 state
[ 0.678257] Monitor-Mwait will be used to enter C-3 state
[ 0.678292] ACPI: CPU0 (power states: C1[C1] C3[C3])
[ 0.678320] processor LNXCPU:00: registered as cooling_device0
[ 0.678323] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 0.678790] ACPI: CPU1 (power states: C1[C1] C3[C3])
[ 0.678817] processor LNXCPU:02: registered as cooling_device1
[ 0.678820] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 0.679281] ACPI: CPU2 (power states: C1[C1] C3[C3])
[ 0.679311] processor LNXCPU:04: registered as cooling_device2
[ 0.679314] ACPI: Processor [CPU2] (supports 8 throttling states)
[ 0.679777] ACPI: CPU3 (power states: C1[C1] C3[C3])
[ 0.679805] processor LNXCPU:06: registered as cooling_device3
[ 0.679808] ACPI: Processor [CPU3] (supports 8 throttling states)
[ 0.682472] Linux agpgart interface v0.103
[ 0.682475] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.683851] brd: module loaded
[ 0.684353] loop: module loaded
[ 0.684449] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.684562] ahci 0000:00:1f.2: version 3.0
[ 0.684576] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.684599] alloc irq_desc for 34 on node 0
[ 0.684601] alloc kstat_irqs on node 0
[ 0.684611] ahci 0000:00:1f.2: irq 34 for MSI/MSI-X
[ 0.704372] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
[ 0.704377] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio slum part ems
[ 0.704386] ahci 0000:00:1f.2: setting latency timer to 64
[ 0.740327] scsi0 : ahci
[ 0.740456] scsi1 : ahci
[ 0.740556] scsi2 : ahci
[ 0.740656] scsi3 : ahci
[ 0.740758] scsi4 : ahci
[ 0.740827] scsi5 : ahci
[ 0.740934] ata1: SATA max UDMA/133 abar m2048@0x93225000 port 0x93225100 irq 34
[ 0.740941] ata2: SATA max UDMA/133 abar m2048@0x93225000 port 0x93225180 irq 34
[ 0.740947] ata3: SATA max UDMA/133 abar m2048@0x93225000 port 0x93225200 irq 34
[ 0.740954] ata4: SATA max UDMA/133 abar m2048@0x93225000 port 0x93225280 irq 34
[ 0.740960] ata5: SATA max UDMA/133 abar m2048@0x93225000 port 0x93225300 irq 34
[ 0.740966] ata6: SATA max UDMA/133 abar m2048@0x93225000 port 0x93225380 irq 34
[ 0.741759] pata_marvell 0000:05:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 0.741778] pata_marvell 0000:05:00.0: setting latency timer to 64
[ 0.741835] scsi6 : pata_marvell
[ 0.741895] scsi7 : pata_marvell
[ 0.741946] ata7: PATA max UDMA/100 cmd 0x1018 ctl 0x1024 bmdma 0x1000 irq 19
[ 0.741947] ata8: PATA max UDMA/133 cmd 0x1010 ctl 0x1020 bmdma 0x1008 irq 19
[ 0.741995] BAR5:00:04 01:7F 02:22 03:C8 04:00 05:00 06:00 07:00 08:00 09:00 0A:00 0B:00 0C:1F 0D:00 0E:00 0F:00
[ 0.742553] Fixed MDIO Bus: probed
[ 0.742557] PPP generic driver version 2.4.2
[ 0.742674] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.742702] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.742714] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 0.742721] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[ 0.742760] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 0.746673] ehci_hcd 0000:00:1a.0: debug port 2
[ 0.746682] ehci_hcd 0000:00:1a.0: cache line size of 32 is not supported
[ 0.746695] ehci_hcd 0000:00:1a.0: irq 16, io mem 0x93225c00
[ 0.760198] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 0.760302] usb usb1: configuration #1 chosen from 1 choice
[ 0.760336] hub 1-0:1.0: USB hub found
[ 0.760340] hub 1-0:1.0: 2 ports detected
[ 0.760393] alloc irq_desc for 23 on node 0
[ 0.760395] alloc kstat_irqs on node 0
[ 0.760398] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.760410] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.760416] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[ 0.760455] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.764364] ehci_hcd 0000:00:1d.0: debug port 2
[ 0.764372] ehci_hcd 0000:00:1d.0: cache line size of 32 is not supported
[ 0.764385] ehci_hcd 0000:00:1d.0: irq 23, io mem 0x93225800
[ 0.776164] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 0.776268] usb usb2: configuration #1 chosen from 1 choice
[ 0.776298] hub 2-0:1.0: USB hub found
[ 0.776302] hub 2-0:1.0: 2 ports detected
[ 0.776353] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.776376] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.776520] PNP: No PS/2 controller found. Probing ports directly.
[ 0.779159] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.779163] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.779255] mice: PS/2 mouse device common for all mice
[ 0.779366] rtc_cmos 00:03: RTC can wake from S4
[ 0.779400] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.779435] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.779544] device-mapper: uevent: version 1.0.3
[ 0.779623] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.779678] device-mapper: multipath: version 1.1.0 loaded
[ 0.779680] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.780034] cpuidle: using governor ladder
[ 0.780471] cpuidle: using governor menu
[ 0.780820] TCP cubic registered
[ 0.780993] NET: Registered protocol family 10
[ 0.781311] lo: Disabled Privacy Extensions
[ 0.781511] NET: Registered protocol family 17
[ 0.781537] Bluetooth: L2CAP ver 2.13
[ 0.781538] Bluetooth: L2CAP socket layer initialized
[ 0.781540] Bluetooth: SCO (Voice Link) ver 0.6
[ 0.781541] Bluetooth: SCO socket layer initialized
[ 0.781554] Bluetooth: RFCOMM TTY layer initialized
[ 0.781556] Bluetooth: RFCOMM socket layer initialized
[ 0.781557] Bluetooth: RFCOMM ver 1.11
[ 0.781758] ACPI Warning: \_PR_.CPU0._PSS: Return type mismatch - found Integer, expected Package 20090521 nspredef-940
[ 0.781763] ACPI: Invalid _PSS data
[ 0.781855] [Firmware Bug]: BIOS needs update for CPU frequency support
[ 0.781897] ACPI Warning: \_PR_.CPU2._PSS: Return type mismatch - found Integer, expected Package 20090521 nspredef-940
[ 0.781900] ACPI: Invalid _PSS data
[ 0.782000] [Firmware Bug]: BIOS needs update for CPU frequency support
[ 0.782040] ACPI Warning: \_PR_.CPU4._PSS: Return type mismatch - found Integer, expected Package 20090521 nspredef-940
[ 0.782044] ACPI: Invalid _PSS data
[ 0.782140] [Firmware Bug]: BIOS needs update for CPU frequency support
[ 0.782180] ACPI Warning: \_PR_.CPU6._PSS: Return type mismatch - found Integer, expected Package 20090521 nspredef-940
[ 0.782184] ACPI: Invalid _PSS data
[ 0.782283] [Firmware Bug]: BIOS needs update for CPU frequency support
[ 0.782398] PM: Resume from disk failed.
[ 0.782408] registered taskstats version 1
[ 0.782490] Magic number: 9:340:655
[ 0.782552] rtc_cmos 00:03: setting system clock to 2009-09-04 23:37:13 UTC (1252107433)
[ 0.782554] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.782555] EDD information not available.
[ 1.059606] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.059642] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.059668] ata6: SATA link down (SStatus 0 SControl 300)
[ 1.059696] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.059746] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.059824] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.059929] ata3.00: ATAPI: ATAPI iHAS120 6, 7L0E, max UDMA/100
[ 1.059948] ata5.00: ATA-7: OCZ-VERTEX v1.10, 1370, max UDMA/133
[ 1.059950] ata5.00: 125045424 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.060204] ata5.00: configured for UDMA/133
[ 1.060929] ata3.00: configured for UDMA/100
[ 1.062773] scsi 2:0:0:0: CD-ROM ATAPI iHAS120 6 7L0E PQ: 0 ANSI: 5
[ 1.067793] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 1.068877] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.068882] Uniform CD-ROM driver Revision: 3.20
[ 1.069238] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 1.069528] sr 2:0:0:0: Attached scsi generic sg0 type 5
[ 1.069575] scsi 4:0:0:0: Direct-Access ATA OCZ-VERTEX v1.10 1370 PQ: 0 ANSI: 5
[ 1.070030] sd 4:0:0:0: [sda] 125045424 512-byte logical blocks: (64.0 GB/59.6 GiB)
[ 1.070056] sd 4:0:0:0: [sda] Write Protect is off
[ 1.070058] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.070071] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.070146] sda:
[ 1.070242] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 1.070311] sda1 sda2 < sda5 >
[ 1.070693] sd 4:0:0:0: [sda] Attached SCSI disk
[ 1.200337] usb 1-1: configuration #1 chosen from 1 choice
[ 1.200902] hub 1-1:1.0: USB hub found
[ 1.201035] hub 1-1:1.0: 6 ports detected
[ 1.242502] Freeing unused kernel memory: 656k freed
[ 1.242623] Write protecting the kernel read-only data: 7532k
[ 1.311663] usb 2-1: new high speed USB device using ehci_hcd and address 2
[ 1.349865] [drm] Initialized drm 1.1.0 20060810
[ 1.447486] usb 2-1: configuration #1 chosen from 1 choice
[ 1.448079] hub 2-1:1.0: USB hub found
[ 1.448255] hub 2-1:1.0: 8 ports detected
[ 1.499075] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
[ 1.499078] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[ 1.500195] alloc irq_desc for 20 on node 0
[ 1.500197] alloc kstat_irqs on node 0
[ 1.500203] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.500207] e1000e 0000:00:19.0: pci_enable_pcie_error_reporting failed 0xfffffffb
[ 1.500290] e1000e 0000:00:19.0: setting latency timer to 64
[ 1.500365] alloc irq_desc for 35 on node 0
[ 1.500366] alloc kstat_irqs on node 0
[ 1.500376] e1000e 0000:00:19.0: irq 35 for MSI/MSI-X
[ 1.699494] ohci1394 0000:06:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.899189] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[93004000-930047ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 2.185016] usb 2-1.4: new high speed USB device using ehci_hcd and address 3
[ 2.205344] 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1c:c0:ef:30:0a
[ 2.205346] 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[ 2.205404] 0000:00:19.0: eth0: MAC: 9, PHY: 0, PBA No: ffffff-0ff
[ 2.274269] PM: Starting manual resume from disk
[ 2.274271] PM: Resume from partition 8:5
[ 2.274272] PM: Checking hibernation image.
[ 2.274326] PM: Resume from disk failed.
[ 2.278072] EXT4-fs (sda1): barriers enabled
[ 2.279557] kjournald2 starting: pid 1135, dev sda1:8, commit interval 5 seconds
[ 2.279573] EXT4-fs (sda1): delayed allocation enabled
[ 2.279576] EXT4-fs: file extents enabled
[ 2.282134] EXT4-fs: mballoc enabled
[ 2.282142] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 2.419868] usb 2-1.4: configuration #1 chosen from 1 choice
[ 2.492167] usb 2-1.6: new full speed USB device using ehci_hcd and address 4
[ 2.611339] udev: starting version 146
[ 2.639303] usb 2-1.6: configuration #1 chosen from 1 choice
[ 2.715579] usb 2-1.7: new full speed USB device using ehci_hcd and address 5
[ 2.809252] usb 2-1.7: configuration #1 chosen from 1 choice
[ 2.809478] hub 2-1.7:1.0: USB hub found
[ 2.809704] hub 2-1.7:1.0: 4 ports detected
[ 2.874621] nvidia: module license 'NVIDIA' taints kernel.
[ 2.874624] Disabling lock debugging due to kernel taint
[ 2.880626] Bluetooth: Generic Bluetooth USB driver ver 0.5
[ 2.880688] usbcore: registered new interface driver btusb
[ 2.999694] alloc irq_desc for 22 on node 0
[ 2.999699] alloc kstat_irqs on node 0
[ 2.999709] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 2.999746] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 3.014999] usb 1-1.5: new full speed USB device using ehci_hcd and address 3
[ 3.090393] hda_codec: Unknown model for ALC889, trying auto-probe from BIOS...
[ 3.090653] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input3
[ 3.115811] usb 1-1.5: configuration #1 chosen from 1 choice
[ 3.123351] usbcore: registered new interface driver hiddev
[ 3.125402] input: Razer Razer Copperhead Laser Mouse as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5:1.0/input/input4
[ 3.125496] generic-usb 0003:1532:0101.0001: input,hidraw0: USB HID v1.00 Mouse [Razer Razer Copperhead Laser Mouse] on usb-0000:00:1a.0-1.5/input0
[ 3.126875] input: Razer Razer Copperhead Laser Mouse as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5:1.1/input/input5
[ 3.126959] generic-usb 0003:1532:0101.0002: input,hidraw1: USB HID v0.01 Keyboard [Razer Razer Copperhead Laser Mouse] on usb-0000:00:1a.0-1.5/input1
[ 3.126968] usbcore: registered new interface driver usbhid
[ 3.126969] usbhid: v2.6:USB HID core driver
[ 3.127973] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.127978] nvidia 0000:01:00.0: setting latency timer to 64
[ 3.128283] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 190.25 Thu Aug 20 16:36:08 PDT 2009
[ 3.174745] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0090270002517e52]
[ 3.186429] cfg80211: Calling CRDA to update world regulatory domain
[ 3.190604] usb 2-1.7.1: new low speed USB device using ehci_hcd and address 6
[ 3.238652] cfg80211: World regulatory domain updated:
[ 3.238654] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 3.238657] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 3.238659] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 3.238660] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 3.238662] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 3.238664] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 3.301353] usb 2-1.7.1: configuration #1 chosen from 1 choice
[ 3.304918] input: G15 Gaming Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.7/2-1.7.1/2-1.7.1:1.0/input/input6
[ 3.304959] generic-usb 0003:046D:C226.0003: input,hidraw2: USB HID v1.10 Keyboard [G15 Gaming Keyboard] on usb-0000:00:1d.0-1.7.1/input0
[ 3.311057] input: G15 Gaming Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.7/2-1.7.1/2-1.7.1:1.1/input/input7
[ 3.311138] generic-usb 0003:046D:C226.0004: input,hiddev96,hidraw3: USB HID v1.10 Device [G15 Gaming Keyboard] on usb-0000:00:1d.0-1.7.1/input1
[ 3.329740] phy0 -> rt2500usb_init_eeprom: Error - Invalid RT chipset detected.
[ 3.329789] phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
[ 3.329855] usbcore: registered new interface driver rt2500usb
[ 3.382240] usb 2-1.7.4: new full speed USB device using ehci_hcd and address 7
[ 3.481250] usb 2-1.7.4: configuration #1 chosen from 1 choice
[ 3.500112] input: G15 GamePanel LCD as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.7/2-1.7.4/2-1.7.4:1.0/input/input8
[ 3.500257] generic-usb 0003:046D:C227.0005: input,hiddev97,hidraw4: USB HID v1.11 Keypad [G15 GamePanel LCD] on usb-0000:00:1d.0-1.7.4/input0
[ 3.602996] phy1: Selected rate control algorithm 'minstrel'
[ 3.603405] Registered led device: rt73usb-phy1::radio
[ 3.603418] Registered led device: rt73usb-phy1::assoc
[ 3.603429] Registered led device: rt73usb-phy1::quality
[ 3.603924] usbcore: registered new interface driver rt73usb
[ 3.755703] lp: driver loaded but no devices found
[ 3.828470] Adding 2594456k swap on /dev/sda5. Priority:-1 extents:1 across:2594456k SS
[ 4.367604] EXT4-fs (sda1): internal journal on sda1:8
[ 5.188184] type=1505 audit(1252107437.914:2): operation="profile_load" pid=1951 name=/usr/sbin/tcpdump
[ 5.196447] type=1505 audit(1252107437.922:3): operation="profile_load" pid=1952 name=/usr/bin/evince
[ 5.201589] type=1505 audit(1252107437.926:4): operation="profile_load" pid=1952 name=/usr/bin/evince-previewer
[ 5.204697] type=1505 audit(1252107437.930:5): operation="profile_load" pid=1952 name=/usr/bin/evince-thumbnailer
[ 5.208888] type=1505 audit(1252107437.934:6): operation="profile_load" pid=1953 name=/usr/share/gdm/guest-session/Xsession
[ 5.210795] type=1505 audit(1252107437.938:7): operation="profile_load" pid=1954 name=/sbin/dhclient3
[ 5.211671] type=1505 audit(1252107437.938:8): operation="profile_load" pid=1954 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 5.212172] type=1505 audit(1252107437.938:9): operation="profile_load" pid=1954 name=/usr/lib/connman/scripts/dhclient-script
[ 5.214416] type=1505 audit(1252107437.942:10): operation="profile_load" pid=1955 name=/usr/lib/cups/backend/cups-pdf
[ 6.507931] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 6.507933] Bluetooth: BNEP filters: protocol multicast
[ 6.513893] Bridge firewalling registered
[ 18.430879] e1000e 0000:00:19.0: irq 35 for MSI/MSI-X
[ 18.457581] ppdev: user-space parallel port driver
[ 18.486690] e1000e 0000:00:19.0: irq 35 for MSI/MSI-X
[ 18.486936] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.495974] rt73usb 2-1.4:1.0: firmware: requesting rt73.bin
[ 18.654433] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 18.919036] CPU0 attaching NULL sched-domain.
[ 18.919040] CPU1 attaching NULL sched-domain.
[ 18.919042] CPU2 attaching NULL sched-domain.
[ 18.919043] CPU3 attaching NULL sched-domain.
[ 18.937135] CPU0 attaching sched-domain:
[ 18.937141] domain 0: span 0-3 level MC
[ 18.937146] groups: 0 1 2 3
[ 18.937149] domain 1: span 0-3 level CPU
[ 18.937151] groups: 0-3 (__cpu_power = 4096)
[ 18.937154] CPU1 attaching sched-domain:
[ 18.937156] domain 0: span 0-3 level MC
[ 18.937157] groups: 1 2 3 0
[ 18.937160] domain 1: span 0-3 level CPU
[ 18.937161] groups: 0-3 (__cpu_power = 4096)
[ 18.937164] CPU2 attaching sched-domain:
[ 18.937165] domain 0: span 0-3 level MC
[ 18.937167] groups: 2 3 0 1
[ 18.937169] domain 1: span 0-3 level CPU
[ 18.937171] groups: 0-3 (__cpu_power = 4096)
[ 18.937173] CPU3 attaching sched-domain:
[ 18.937175] domain 0: span 0-3 level MC
[ 18.937176] groups: 3 0 1 2
[ 18.937179] domain 1: span 0-3 level CPU
[ 18.937180] groups: 0-3 (__cpu_power = 4096)
[ 20.879534] CPU0 attaching NULL sched-domain.
[ 20.879538] CPU1 attaching NULL sched-domain.
[ 20.879539] CPU2 attaching NULL sched-domain.
[ 20.879541] CPU3 attaching NULL sched-domain.
[ 20.896239] CPU0 attaching sched-domain:
[ 20.896242] domain 0: span 0-3 level MC
[ 20.896244] groups: 0 1 2 3
[ 20.896248] CPU1 attaching sched-domain:
[ 20.896250] domain 0: span 0-3 level MC
[ 20.896251] groups: 1 2 3 0
[ 20.896254] CPU2 attaching sched-domain:
[ 20.896256] domain 0: span 0-3 level MC
[ 20.896257] groups: 2 3 0 1
[ 20.896260] CPU3 attaching sched-domain:
[ 20.896261] domain 0: span 0-3 level MC
[ 20.896263] groups: 3 0 1 2

Related Articles
Featured Articles
Trending Linux News