Tweet
have a monitor with native resolution of 1600*900_60.00, and the intel on board Gen3 Xeon video chipset (i915).
when i do "$> xrandr" the 1600x900 resolution is not in the list. I tried to write an xorg configuration for monitor and I placed it on /etc/X11/xorg.conf.d/10-monitor.conf. but i must mess some value in there up; that it ha no effect and doesn't change the resolution.
I am sure the /etc/X11/xorg.conf.d/10-monitor.conf is being read at "$> startx" because if i put anything wrong like ()*! at that file X won't start and produce an error.
The cvt 1600 900 returns:
I have a monitor with native resolution of 1600*900_60.00, and the intel on board Gen3 Xeon video chipset (i915).
when i do $> xrandr the 1600x900 resolution is not in the list. I tried to write an xorg configuration for monitor and I placed it on /etc/X11/xorg.conf.d/10-monitor. but i must mess some value in there up; that it ha no effect and doesn't change the resolution.
I am sure the /etc/X11/xorg.conf.d/10-monitor is being read at $> startx because if i put anything wrong like ()*! at that file X won't start and produce an error.
The cvt 1600 900 returns:
also the xrandr produce:
when i do "$> xrandr" the 1600x900 resolution is not in the list. I tried to write an xorg configuration for monitor and I placed it on /etc/X11/xorg.conf.d/10-monitor.conf. but i must mess some value in there up; that it ha no effect and doesn't change the resolution.
I am sure the /etc/X11/xorg.conf.d/10-monitor.conf is being read at "$> startx" because if i put anything wrong like ()*! at that file X won't start and produce an error.
The cvt 1600 900 returns:
I have a monitor with native resolution of 1600*900_60.00, and the intel on board Gen3 Xeon video chipset (i915).
when i do $> xrandr the 1600x900 resolution is not in the list. I tried to write an xorg configuration for monitor and I placed it on /etc/X11/xorg.conf.d/10-monitor. but i must mess some value in there up; that it ha no effect and doesn't change the resolution.
I am sure the /etc/X11/xorg.conf.d/10-monitor is being read at $> startx because if i put anything wrong like ()*! at that file X won't start and produce an error.
The cvt 1600 900 returns:
Code:
1600x900 59.95 Hz (CVT 1.44M9) hsync: 55.99 kHz; pclk: 118.25 MHz Modeline "1600x900_60.00" 118.25 1600 1696 1856 2112 900 903 908 934 -hsync +vsync
Code:
$> xrandr
Screen 0: minimum 320 x 200, current 1024 x 768, maximum 8192 x 8192
VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm
1024x768 60.0*
800x600 60.3 56.2
848x480 60.0
640x480 59.9
HDMI1 disconnected (normal left inverted right x axis y axis)
DP1 disconnected (normal left inverted right x axis y axis)
HDMI2 disconnected (normal left inverted right x axis y axis)
HDMI3 disconnected (normal left inverted right x axis y axis)
DP2 disconnected (normal left inverted right x axis y axis)
DP3 disconnected (normal left inverted right x axis y axis)
1600x900_60.00�� (0xa5) 118.2MHz
h: width 1600 start 1696 end 1856 total 2112 skew 0 clock 56.0KHz
v: height 900 start 903 end 908 total 934
And this is my 10-monitor.config file:
Section "Device"
Identifier "Intel i915"
Option "VGA1" #"VGA screen"
Driver "intel"
EndSection
Section "Monitor"
Identifier "Primary Monitor"
Modeline "1600x900_60.00" 118.25 1600 1696 1856 2112 900 903 908 934 -Hsync +Vsync
Option "PreferredMode" "1600x900"
EndSection
Section "Screen"
Identifier "Screen0"
Device "VGA1"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1600x900_60.00"
EndSubSection
EndSection