anybody sucess with external Montior on v5250 ?

[oehmes]

Hi,

i tried all kind of combos in xorg.conf with radeonhd, but i am not able to get my external monitor to work (LCD works fine) ..

....

(II) RADEONHD(0): I2C device "RHD I2C line 2:ddc2" registered at address 0xA0.
(II) RADEONHD(0): I2C device "RHD I2C line 2:ddc2" removed.
(II) RADEONHD(0): EDID data for LVDS Panel
(II) RADEONHD(0): Manufacturer: IBM Model: 2887 Serial#: 0
(II) RADEONHD(0): Year: 2005 Week: 0
(II) RADEONHD(0): EDID Version: 1.3
(II) RADEONHD(0): Digital Display Input
(II) RADEONHD(0): Max H-Image Size [cm]: horiz.: 33 vert.: 21
(II) RADEONHD(0): Gamma: 2.20
(II) RADEONHD(0): No DPMS capabilities specified; RGB/Color Display
(II) RADEONHD(0): First detailed timing is preferred mode
(II) RADEONHD(0): redX: 0.596 redY: 0.347 greenX: 0.335 greenY: 0.543
(II) RADEONHD(0): blueX: 0.158 blueY: 0.143 whiteX: 0.313 whiteY: 0.329
(II) RADEONHD(0): Manufacturer's mask: 0
(II) RADEONHD(0): Supported additional Video Mode:
(II) RADEONHD(0): clock: 122.0 MHz Image Size: 331 x 207 mm
(II) RADEONHD(0): h_active: 1680 h_sync: 1712 h_sync_end 1776 h_blank_end 1904 h_border: 0
(II) RADEONHD(0): v_active: 1050 v_sync: 1051 v_sync_end 1054 v_blanking: 1066 v_border: 0
(II) RADEONHD(0): Supported additional Video Mode:
(II) RADEONHD(0): clock: 101.7 MHz Image Size: 331 x 207 mm
(II) RADEONHD(0): h_active: 1680 h_sync: 1712 h_sync_end 1776 h_blank_end 1904 h_border: 0
(II) RADEONHD(0): v_active: 1050 v_sync: 1051 v_sync_end 1054 v_blanking: 1066 v_border: 0
(II) RADEONHD(0): LP154W02-TL06
(II) RADEONHD(0): EDID (in hex):
(II) RADEONHD(0): 00ffffffffffff00244d872800000000
(II) RADEONHD(0): 000f0103802115780abca59858558b28
(II) RADEONHD(0): 24505400000001010101010101010101
(II) RADEONHD(0): 010101010101a82f90e0601a10402040
(II) RADEONHD(0): 13004bcf10000019b72790e0601a1040
(II) RADEONHD(0): 204013004bcf100000190000000f00b3
(II) RADEONHD(0): 0a32b30a28140100320c0000000000fe
(II) RADEONHD(0): 004c503135345730322d544c3036007f
(II) RADEONHD(0): Connector "PANEL LCD1" uses Monitor "LVDS Panel":
Bandwidth: 122MHz
Horizontal timing:
64.1 - 64.1kHz
Vertical timing:
60.1 - 60.1Hz
Allows reduced blanking.
Uses Fixed Modes.
Attached modes:
Modeline "1680x1050" 122.00 1680 1712 1776 1904 1050 1051 1054 1066
(II) RADEONHD(0): Listing modesetting layout:

CRTC 1: tied to PLL 1 and LUT A:
Outputs: DAC A (VGA CRT1)

CRTC 2: tied to PLL 2 and LUT B:
Outputs: LVDS/TMDS (PANEL LCD1)

Unused Outputs: TMDS A

(==) RADEONHD(0): RGB weight 888
(==) RADEONHD(0): Default visual is TrueColor
(==) RADEONHD(0): Using gamma correction (1.0, 1.0, 1.0)
(II) RADEONHD(0): Validating Fixed Modes from Monitor "LVDS Panel"
on Connector "PANEL LCD1"
(II) RADEONHD(0): Rejected mode "1680x1050" (1680x1050:122.0Mhz): mode clock too high
(EE) RADEONHD(0): No valid modes found
(II) RADEONHD(0): Destroying DAC A
(II) RADEONHD(0): Destroying LVDS/TMDS
(II) RADEONHD(0): Destroying TMDS A
(II) RADEONHD(0): I2C bus "RHD I2C line 0" removed.
(II) RADEONHD(0): I2C bus "RHD I2C line 1" removed.
(II) RADEONHD(0): I2C bus "RHD I2C line 2" removed.
(II) UnloadModule: "radeonhd"
(EE) Screen(s) found, but none have a usable configuration.

Fatal server error:
no screens found


also a fresh config doesn't work if i have an external monitor attached .. as soon as i disconnect, it works again with the lcd .

any ideas ?