hi yall,
i installed the official cat. 10.10 for 32 bit ubuntu 10.10. i am also using a crossfire chain with a 5750 & 5770 and i think its working. therefore, i used the guide here on phoronix.
i did not install cat. control center. now, is there a way to tweak all those settings manually, like in xorg conf? and what are all the available options to do so, is there a list somewhere?
my xorg.conf looks like this atm:
what should i change about this xorg.conf, when i want to have even better performance for games and desktop applications?
second, is direct2d accel. enabled by default with this driver? and would you recommend to enable it? which different modes exist to accelerate 2d?
third, how would i configure an automatic switching low power state for 2d and a high power state for 3d? or how can i make a permanent overclocking? i see there are some options in aticonfig.
fourth, i see the crossfire chain is enabled, but how can i really check if its actually 100% working or being used by an application (for example heroes of newerth)?
fifth, would you recommend to install opencl driver? what applications will profit of it?
best regards
i installed the official cat. 10.10 for 32 bit ubuntu 10.10. i am also using a crossfire chain with a 5750 & 5770 and i think its working. therefore, i used the guide here on phoronix.
i did not install cat. control center. now, is there a way to tweak all those settings manually, like in xorg conf? and what are all the available options to do so, is there a list somewhere?
my xorg.conf looks like this atm:
Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
EndSection
Section "Module"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
Monitor "aticonfig-Monitor[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
EndSection
Section "Module"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
Monitor "aticonfig-Monitor[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
second, is direct2d accel. enabled by default with this driver? and would you recommend to enable it? which different modes exist to accelerate 2d?
third, how would i configure an automatic switching low power state for 2d and a high power state for 3d? or how can i make a permanent overclocking? i see there are some options in aticonfig.
fourth, i see the crossfire chain is enabled, but how can i really check if its actually 100% working or being used by an application (for example heroes of newerth)?
fifth, would you recommend to install opencl driver? what applications will profit of it?
best regards
Comment