Hi,
I'm having difficulty running tests from the PTS gui. From the command line I can run, e.g.
:?suite/installed-tests/scimark2$ ./scimark2
** **
** SciMark2 Numeric Benchmark, see //math.nist.gov/scimark **
** for details. (Results can be submitted to pozo) **
** **
Using 2.00 seconds min time per kenel.
Composite Score: 399.45
FFT Mflops: 211.68 (N=1024)
SOR Mflops: 917.60 (100 x 100)
MonteCarlo: Mflops: 81.34
Sparse matmult Mflops: 340.45 (N=1000, nz=5000)
LU Mflops: 446.19 (M=100, N=100)
But from the gui running this test gives errors
====================================
Test Configuration: SciMark
====================================
====================================
SciMark (Run 1 of 4)
====================================
sh: -c: is not an identifier
sh: -c: is not an identifier
====================================
SciMark (Run 2 of 4)
====================================
sh: -c: is not an identifier
sh: -c: is not an identifier
====================================
SciMark (Run 3 of 4)
====================================
sh: -c: is not an identifier
sh: -c: is not an identifier
====================================
SciMark (Run 4 of 4)
====================================
sh: -c: is not an identifier
sh: -c: is not an identifier
####################################
SciMark:
Computational Test: Composite
Average: 0.00 Mflops
####################################
The scripts in the phoronix directory have shebang lines #!/bin/sh,
on my Open Solaris distribution this points to the korn shell (ksh). Could this be the cause of the problem? Has anyone had experience with this or could anyone recommend a fix?
On a perhaps unrelated note, After downloading tests, I had to go to the test instalation dir, unzip the downloaded file, and gmake the test.
Cheers
I'm having difficulty running tests from the PTS gui. From the command line I can run, e.g.
:?suite/installed-tests/scimark2$ ./scimark2
** **
** SciMark2 Numeric Benchmark, see //math.nist.gov/scimark **
** for details. (Results can be submitted to pozo) **
** **
Using 2.00 seconds min time per kenel.
Composite Score: 399.45
FFT Mflops: 211.68 (N=1024)
SOR Mflops: 917.60 (100 x 100)
MonteCarlo: Mflops: 81.34
Sparse matmult Mflops: 340.45 (N=1000, nz=5000)
LU Mflops: 446.19 (M=100, N=100)
But from the gui running this test gives errors
====================================
Test Configuration: SciMark
====================================
====================================
SciMark (Run 1 of 4)
====================================
sh: -c: is not an identifier
sh: -c: is not an identifier
====================================
SciMark (Run 2 of 4)
====================================
sh: -c: is not an identifier
sh: -c: is not an identifier
====================================
SciMark (Run 3 of 4)
====================================
sh: -c: is not an identifier
sh: -c: is not an identifier
====================================
SciMark (Run 4 of 4)
====================================
sh: -c: is not an identifier
sh: -c: is not an identifier
####################################
SciMark:
Computational Test: Composite
Average: 0.00 Mflops
####################################
The scripts in the phoronix directory have shebang lines #!/bin/sh,
on my Open Solaris distribution this points to the korn shell (ksh). Could this be the cause of the problem? Has anyone had experience with this or could anyone recommend a fix?
On a perhaps unrelated note, After downloading tests, I had to go to the test instalation dir, unzip the downloaded file, and gmake the test.
Cheers
Comment