If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Same problem, or what challenge are you now facing?
It stopped at "Completely removed ntfsprogs" (the progress bar stuck at 97%). This is just one of the places it might hang during install...
Tomorrow, I'll try installing windows on the drive to see if that works. That will at least rule out the drive being bad. If Windows Installs, I'll try installing Linux in a dual boot setup on that drive. It'll be downright dirty shame to give up so much hard drive space (by having a windows partition) just to make it work...
The new motherboard came with bios v1.9 on it, and i'm almost positive that flashing it to 2.1 won't help/matter.
My question is how in the hell did Phoronix get Linux installed on this motherboard because it sure ain't workin' for me.
It boots the Ubunutu Live CD just fine (including sound and NIC support).
So is the issue really the Ubuntu installer not working? If you are not completely oriented around Ubuntu then consider Gentoo. If the Gentoo LiveCD boots you can do the Gentoo install from a console and skip all the fancy stuff.
I cannot say how many times I had similar problems with Fedora installs not understanding hardware. Never had after 3+ years a Gentoo install fail yet.
mirror mirror on the wall, what is the distro to rule them all
I've tried a _lot of_ distros the past week, since I was convinced there exist distros simple enough that even my mom can install them. Unfortunately the simpler a distro, the more it tries to hide, such as boot messages. I tried Ubuntu, Suse, Knoppix, Ark Linux (rc2) and Mandriva and they all made it difficult to do troubleshooting. I needed ide=nodma boot option, but even with that I suspect my cdrom drive was flaky as a lot of installs would fail at random points. Eventually I decided to do the install myself and use Gentoo, since I've had good experience with it. I cached the install cd (docache) and proceeded with the install. I had to redo mke2fs of my partitions, because they failed the first time because of some strange dma error (even with ide=nodma). The good thing is that I was right there to see what was going wrong and fix it trivially. No automated installer does that (yet). I've also had very good experiences with knoppix in the past, but for some reason I couldn't get it to work even with ide=nodma this time. Oh well.
Well, I tried to install XP on the same 200gb drive, and configured it to only use a 50gb partition. It would not finish the install. So, my new 200gb hard drive just mighht be defective. I'm going to take it back to Best Buy for an exchange, and see if things don't work a little better.
I'll be back with an update later dtoday.
If nothing else, I'm tenacious (or if you could say I'm too stupid to quit).
Did you try using Ubuntu or any other distributions?
You seem to be having lots of bad luck, unfortunately.
I started with Ubunutu 6.06 (burned at 48x, 24x, and 8x), tried the Ubuntu Alternate CD, XUbuntu, 64-bit Ubuntu, Kubuntu, Ubuntu 5.10, Knoppix, Suse 10.1, Debian, and finally Fedora Core 5. This means I've tried kernel versions from 2.6.13 through 2.6.17. I've tried two copies of the same motherboard with BIOS versions from 1.50 to 2.10, tried enabling and disabling various items in the BIOS, exchanged a harddrive, increased and decreased the amount of memory in the box, and even different CPUs.
I think you can say I've pretty much tried everything. Most of the time, the install process wouldn't complete, but if it did, the machine wouldn't boot.
I'm aware that other people have gotten Linux to run on this motherboard, but IMHO, it's generally incompatible.